Alcormp.exe -
The Alcorithm software, and subsequently Alcormp.exe, was created to provide a specific service. The software appears to be designed for algorithmic trading, allowing users to automate their trading strategies. Alcormp.exe is likely a component of this software, responsible for executing specific tasks.
Click to begin the low-level formatting and firmware flashing process.
✅ Legitimate (Usually) Manufacturer: Alcor Micro, Corp. Primary Function: USB Flash Drive MP Tool (Mass Production Tool) alcormp.exe
: Repairing "fake" drives (often called "Frankenflashes") that claim to be 64GB but are actually 4GB.
| Step | Action | ⚠️ Critical Notes & Warnings | | :--- | :--- | :--- | | | Identify Your USB Drive's Controller | Before downloading anything, use a free tool like ChipGenius or USBDeview to check your USB drive's Chip Vendor and Chip Part-Number . Only proceed if it says something like "Alcor Micro" or "AU698x/FC8xxx". | | 2 | Back Up All Data from the USB Drive | This is the most important step. Mass production will completely erase all data, files, and partitions on the drive. Do not skip this. | | 3 | Download the Correct Tool Version | Download the specific version of the AlcorMP tool designed for your chip's model number (e.g., AU698X, FC8308). Download it from reputable sources. | | 4 | Run AlcorMP.exe as Administrator | Right-click on AlcorMP.exe and select "Run as administrator." This grants the tool the necessary low-level hardware access. | | 5 | Configure the Tool Settings | The interface may look complex. For a basic restore, look for a "Setup" or "Setting" button. Key settings to check: - Partition Setting: Choose "Removable Disk" for a standard USB drive. - Format: Select a Low Level Format for a thorough repair. - File System: Select FAT32 or NTFS as needed. - VID/PID: Do not change these unless you have a specific reason. | | 6 | Connect the USB Drive | After configuring the settings, save them and return to the main screen. Now, plug in your USB drive. The tool should detect it automatically. | | 7 | Start the Process | Once the drive is detected, click the "Start" button to begin the process. | | 8 | Never Interrupt the Process | Do not unplug the USB drive or close the software until it is 100% complete. Interruption can permanently damage the drive. | | 9 | Safe Removal and Testing | Once finished, use Windows' "Safely Remove Hardware" option to eject the drive. Unplug it, then plug it back in. You should now see a healthy USB drive in File Explorer. | The Alcorithm software, and subsequently Alcormp
Extract the downloaded AlcorMP ZIP archive to a local folder. Right-click and select Run as Administrator .
Match your and your NAND Flash Memory ID (FID) code discovered via ChipGenius to the corresponding tool description. Click to begin the low-level formatting and firmware
| Check | Legitimate Indicator | Suspicious Indicator | |-------|----------------------|----------------------| | | C:\Windows\System32\drivers\ or C:\Program Files (x86)\Alcor Micro\Smart Card Reader\ | Anywhere in Temp , AppData\Local\Temp , Downloads , or C:\Users\Public | | Digital Signature | Signed by "Alcor Micro Corp." | No signature, or signed by unknown publisher | | File Size | Typically between 150 KB – 500 KB | Very small (under 50KB) or very large (over 1MB) | | Process Behavior | Idles until a smart card is inserted | Constantly runs at high CPU, phones home to IP addresses |
The software will begin scanning the NAND memory, sorting out bad sectors, and rewriting the controller's instruction set. The operation can take anywhere from two minutes to an hour depending on the size and speed of your flash drive. Troubleshooting Common AlcorMP Errors Error Code / Issue Root Cause "Hub Configuration Changed" The USB port changed states or lost power. Use a USB 2.0 port on the back of the PC. Drive Not Detected (Gray Boxes) Missing driver or incompatible tool version.